We recommend to run a new node, if you want to add an additional hard drive.
All nodes behind the same subnet /24 of a public IP are treated as a single node for ingress traffic and as separate ones for egress traffic (to the customers, repair and audit) - this is because we want to be decentralized as much as possible.
Adding more drives/nodes will not increase the ingress traffic, only usage by customers can do this.
You can, of course, use RAID instead, but this reduncancy not required for the network's operation - the network itself has a built-in redundancy due to the usage of erasure codes: the customer needs only a subset of pieces out of total to reconstruct the whole file.
If you would like to use RAID anyway, please note - your node will not receive more customer data only because you use RAID, this will not affect the node selection.
Using RAID0 (LVM, spanned drives, JBOD, etc.) is not recommended - with only one disk failure the whole node is lost.
Even using RAID5/6 with today's disks is too risky due to bit failure rate on disks with high capacity: High risk to lose a RAID5 volume during rebuild.
You can also read the discussion RAID vs No RAID on our forum.
Each node must have its own generated unique identity signed with a new authorization token. Using a copy of the same identity but different tokens will result in disqualification as it is the same identity but with missing data.
If you have only one external address, then you need to have a unique port for each storagenode. The default port for storagenode is
If you want to add an additional new node, you can use the next free port or simply increase the previous used port by 1, for example -
If you run multiple nodes on the same device, you will need a unique port for the dashboard too. The default port for the dashboard is
You can use the same rule as for the node's port to select any free port or simply increase the port number by 1, for example -
14003. Don't forget to uncomment the parameter in your config (remove
# with space after, each option should be started without spaces)!
You need to forward only the external node's port. Please, do not forward the dashboard's port - it has no protection and anyone on the internet can see your private information. See How to remote access the web dashboard guide to connect to your dashboard remotely.
If you run a binary version of storagenode (GUI Install - Windows for example) or a docker version with
--network host option, you also need to have unique internal ports.
For the node's CLI dashboard, the default internal address and port is
127.0.0.1:7778, it is specified in the
For the second and any further nodes, you need to specify a unique port for each node there, too.
The next parameter to change the port is
server.address, it contains an internal listen node's address and port, specified as
:28967 (this is equivalent to
0.0.0.0:28967, i.e. it will bind to any local IP) by default.
You need to make these changes for the second and any further additional nodes as well.
For example, you decided to configure your second node with port
28968. Then you can forward this port to the internal
28967 port, if the destination local IP is different from the first node. If both nodes are running on the same host, then you need to forward
28968 and use this port in the
contact.external-address: option of the
config.yaml (in case of binary) or
-e ADDRESS parameter of
docker run in case of docker. If you use a binary version (or
docker run with
--network host), you also need to specify this port in the
you need to change the
config.yamlin case of binary or
-e ADDRESSparameter of
docker runin case of docker to use the external address and port, i.e.
if the second node is running on another device, you can forward
28967, nothing else is needed to change in the second node configuration except the external address above;
if the second node is running on the same device as the first one, you need to forward
28968, change the
server.address:option in the
config.yaml(in case of binary or
--network host) or
-p 28968:28967parameter in
docker runcommand (in case of docker without
We assume that the second node would be run on the same device as a first one.
Go to your router and forward port
28968and the IP of your device.
docker runwill contain:
Please, use the full command from Storage Node, the above is an excerpt showing only the changed parts.
We assume that the second node would be run on the same device as the first one.
The Windows GUI installer can install only one node on the same Windows PC. For the second and next nodes we support only the docker version: CLI Install.
The alternative is to use the unofficial, Community supported Windows Toolbox made by @Vadim: Win GUI Storj Node Toolbox, it allows you to set up more than one Windows node on the same PC.
- Go to your router and forward port
28968and IP of your device.
Change parameters in your
config.yaml (see Where can I find the config.yaml?):
3. Save the
config.yaml and restart the
storagenode service (see How do I shut down my node for system maintenance?).